P0302 Code: Cylinder 2 Misfire? Find the Cause by When It Happens

Cylinder 2 is misfiring, and your engine computer has already narrowed it down for you. A P0302 code means the computer detected cylinder 2 failing to fire properly, usually because of a spark plug, an ignition coil, or a fuel injector on that cylinder. The quickest way to work out which one is to pay attention to when the misfire happens.

Handheld OBD2 scanner next to the diagnostic port, ready to read a P0302 code

Quick answer

QuestionShort answer
What it meansCylinder 2 misfire detected
Most common causesSpark plug, ignition coil, or fuel injector
Also commonRecent plug or coil work, a vacuum leak, low compression
SymptomsRough idle, hesitation, shaking, check engine light
Safe to drive?Gently, if the light is steady. Not if it’s flashing
Typical cost$20–$350 for most fixes

When does it misfire? Use that to narrow it down

When the misfire shows upMost likely cause
Under load: accelerating, climbing hills, passingIgnition: a worn plug or a weak coil
Only at idle, smooths out when you revVacuum leak near cylinder 2, or a weak injector
Mostly on cold starts, then clears upWeak coil, leaking injector, or carbon on the intake valves (direct-injection engines)
Right after a tune-up or coil replacementUnplugged connector, unseated boot, or wrong plug gap
All the time, rough at every speedDead coil, failed injector, or low compression
After heavy rain or a car washMoisture getting into a cracked coil or plug boot

Symptoms of a P0302 code

  • A rough or shaky idle, often felt through the seat and steering wheel. See car shakes when idling.
  • Hesitation or stumbling when you press the gas. See car jerks when accelerating.
  • Less power and worse fuel economy.
  • A flashing check engine light under load, which means the misfire is severe.

Common causes in more detail

1. A worn or fouled spark plug

Plugs wear gradually. A tired one may fire fine at idle but fail under load, when it takes more voltage to jump the gap. If yours are due, replace the full set.

2. A weak or cracked ignition coil

Coils crack from years of heat cycles. Once cracked, they can leak spark to the engine, especially when moisture gets in, which is why some misfires only show up on cold, damp mornings.

3. Something disturbed during recent work

This is the most overlooked cause. If the code appeared right after new plugs or coils, check that every connector clicked fully into place, every coil boot is seated, and the plug for cylinder 2 was gapped and tightened correctly. It’s often a free fix.

4. A fuel injector problem

A clogged injector starves cylinder 2 of fuel, and a leaking one floods it, especially after the car sits. On direct-injection engines, carbon can also build up on the intake valves over time and cause misfires that are worst on cold starts.

5. A vacuum leak near cylinder 2

A cracked hose or leaking intake gasket near cylinder 2 lets in extra air. That cylinder runs lean, mostly at idle. You may also see a lean code like P0171.

6. Low compression

A burnt valve, worn piston rings, or a failing head gasket can stop cylinder 2 from sealing. If you also see thick white smoke that doesn’t clear, read white smoke from exhaust when cold.

Confirm it with a swap test

On engines with one coil per cylinder, swap the cylinder 2 coil with its neighbor, then drive until the light returns or check for pending codes. If the code moves with the coil, becoming P0301 or P0303, the coil is bad. If it stays on cylinder 2, swap the spark plugs the same way. If it still won’t move, the injector, a vacuum leak, or compression is the next suspect. Our P0301 code guide walks through the swap test step by step.

Where cylinder 2 sits depends on your engine. On many inline engines it’s next to cylinder 1, but on V6 and V8 engines it can be on the opposite side, so check a diagram for your exact engine before you start. Many inexpensive scanners can also show live misfire counts for each cylinder, which lets you confirm a fix without waiting for the light.

How much does it cost to fix a P0302 code?

RepairDIY partsShop price
Reseat a connector or coil boot$0$50–$100 for diagnosis
Spark plugs (full set)$30–$120$150–$400
Ignition coil (one)$40–$150$150–$350
Fuel injector (one)$60–$250$200–$600
Vacuum leak repair (hose or gasket)$10–$80$100–$400
Intake valve carbon cleaning (direct injection)—$300–$800
Compression test—$100–$250

It’s also worth entering your VIN in the NHTSA recall lookup before buying parts, in case a recall or free repair covers your engine.

Can I keep driving with a P0302 code?

If the check engine light is steady and the engine only runs a little rough, short and gentle trips are usually fine until you can fix it. Skip hard acceleration, towing, and long highway runs.

If the light is flashing, the misfire is severe. Unburned fuel is reaching the exhaust and can overheat the catalytic converter quickly, turning a cheap coil or plug into an expensive P0420 repair. Ease off and get it checked soon; our guide on check engine light flashing explains why.

If your scanner shows misfires on several cylinders, read our P0300 code guide instead. You can look up any code in our OBD2 code lookup, or start from symptoms with the free car symptom checker.

Free tools from GarageWise HQ

Car Symptom Checker: not sure what's wrong? Answer two quick questions to narrow it down.

OBD2 Code Lookup: got a check engine code? See what it means and what the fix usually costs.

About the author: Muhammad Umair Naseer

Muhammad Umair Naseer is the founder and editor of GarageWise HQ. A software engineer by training, he started the site to turn confusing car problems into clear, practical guides. Every article is researched from owner's manuals, manufacturer service information, and trusted repair resources, and when a job needs a certified mechanic, he says so.